If checked, do not create _GSDATA_ folder in the sync folder on the Left/Right side of the job. No _gsdata_ folder here (un-checked by default) If unchecked and if FAT is not reported by FS, assume that the file system stores file mod time in UTC. If checked, use special time adjustment designed to neutralize FAT time storage problems. Works only in NTFS, decompression will be done by Windows.įAT file system that does not reveal itself (Windows only, un-checked by default) If checked, decompress file bodies using native file system functionality. Uncompress (Windows only, un-checked by default) If checked, compress file bodies using native file system functionality. If unchecked, Extended Attributes are copied only when the changed file is copied.Ĭompress (Windows only, un-checked by default) If checked, changes in Extended Attributes are detected even when the file body does not change. If unchecked, ACL is copied only when the file body has changed.Ĭompare Extended Attributes (Mac only, un-checked by default) If checked, changes in ACL are detected even when the file body does not change. If unchecked, the File Owner is copied only when the file body has changed. If checked, changes in the File Owner are detected even when the file body does not change. If checked, changes in file/folder Permissions are detected even when the file body does not change. If unchecked, Permissions are copied only when the changed file is copied. If unchecked, Attributes are copied only when the changed file is copied.Ĭompare Permissions (Mac and Unix only, unchecked by default) If checked, changes in file/folder Attributes are detected even when the file body does not change. If unchecked, the file is only considered to be changed if the File Size or File Mod Time has changed.Ĭompare Attributes (Windows only, un-checked by default) If the MD5 checksum of the file differs, but the File Size and File Mod Time are the same, declare a conflict.Īfter Sync, verify that the checksum of the copied file is the same on both sides. If checked, compare the MD5 checksum of the Old to the New file if the file size has not changed, but the file mod time has. On the Profile page, select the network location types to which this rule applies, and then click Next.In the Left Folder and Right Folder tabs, you may set the locations of your job and configure options.Ĭlick on "Show Options" to list all options for the selected Left or Right side.Ĭompare Checksums when needed (slower) (un-checked by default) On the Action page, select Allow the connection, and then click Next. Configure as appropriate for your design, and then click Next. On the Scope page, you can specify that the rule applies only to network traffic to or from the IP addresses entered on this page. When you have configured the protocols and ports, click Next. To select a protocol by its number, select Custom from the list, and then type the number in the Protocol number box. If you select another protocol, then only packets whose protocol field in the IP header match this rule are permitted through the firewall. Because this is an incoming rule, you typically configure only the local port number. To restrict the rule to a specified port number, you must select either TCP or UDP. On the Protocol and Ports page, select the protocol type that you want to allow. If you choose to do this, follow the steps in the Create an Inbound Program or Service Rule procedure in addition to the steps in this procedure to create a single rule that filters network traffic using both program and port criteria. The specified program cannot receive network traffic on other ports, and other programs cannot receive network traffic on the specified port. If you combine the rule types, you get a firewall rule that limits traffic to a specified port and allows the traffic only when the specified program is running. This type of rule is often combined with a program or service rule. On the Rule Type page of the New Inbound Rule Wizard, click Custom, and then click Next. In the navigation pane, click Inbound Rules. Open the Group Policy Management Console to Windows Defender Firewall with Advanced Security. This topic describes how to create a standard port rule for a specified protocol or TCP or UDP port number. To complete these procedures, you must be a member of the Domain Administrators group, or otherwise be delegated permissions to modify the GPOs. This type of rule allows any program that listens on a specified TCP or UDP port to receive network traffic sent to that port. With Advanced Security node in the Group Policy Management MMC snap-in to create firewall rules. To allow inbound network traffic on only a specified TCP or UDP port number, use the Windows Defender Firewall
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |